Order nr_pucchsim options alphabetically in help

openair1/SIMULATION/NR_PHY/pucchsim.c

@@ -347,36 +347,35 @@ int main(int argc, char **argv)
     default:
     case 'h':
       printf("%s -h(elp) -p(extended_prefix) -N cell_id -f output_filename -F input_filename -g channel_model -n n_frames -t Delayspread -s snr0 -S snr1 -x transmission_mode -y TXant -z RXant -i Intefrence0 -j Interference1 -A interpolation_file -C(alibration offset dB) -N CellId\n", argv[0]);
-      printf("-h This message\n");
-      printf("-p Use extended prefix mode\n");
+      //printf("-C Generate Calibration information for Abstraction (effective SNR adjustment to remove Pe bias w.r.t. AWGN)\n");
+      printf("-A Interpolation_filname Run with Abstraction to generate Scatter plot using interpolation polynomial in file\n");
+      printf("-b number of HARQ bits (1-2)\n");
+      printf("-B payload to be transmitted on PUCCH\n");
+      printf("-c Activate scheduling request\n");
       printf("-d Use TDD\n");
+      printf("-f Output filename (.txt format) for Pe/SNR results\n");
+      printf("-F Input filename (.txt format) for RX conformance testing\n");
+      printf("-g [A,B,C,D,E,F,G] Use 3GPP SCM (A,B,C,D) or 36-101 (E-EPA,F-EVA,G-ETU) models (ignores delay spread and Ricean factor)\n");
+      printf("-i Enter number of ofdm symbols for pucch\n");
+      printf("-I Starting symbol index for pucch\n");
+      printf("-h This message\n");
+      printf("-m initial cyclic shift m0\n");
       printf("-n Number of frames to simulate\n");
+      printf("-N Nid_cell\n");
+      printf("-o Carrier frequency offset in Hz\n");
+      printf("-O oversampling factor (1,2,4,8,16)\n");
+      printf("-p Use extended prefix mode\n");
+      printf("-P Enter the format of PUCCH\n");
+      printf("-q PUCCH number of PRB\n");
+      printf("-r PUCCH starting PRB\n");
+      printf("-R N_RB_DL\n");
       printf("-s Starting SNR, runs from SNR0 to SNR0 + 5 dB.  If n_frames is 1 then just SNR is simulated\n");
       printf("-S Ending SNR, runs from SNR0 to SNR1\n");
       printf("-t Delay spread for multipath channel\n");
-      printf("-g [A,B,C,D,E,F,G] Use 3GPP SCM (A,B,C,D) or 36-101 (E-EPA,F-EVA,G-ETU) models (ignores delay spread and Ricean factor)\n");
+      printf("-T to check nacktoack miss for format 1\n");
       printf("-x Transmission mode (1,2,6 for the moment)\n");
       printf("-y Number of TX antennas used in eNB\n");
       printf("-z Number of RX antennas used in UE\n");
-      printf("-i Relative strength of first intefering eNB (in dB) - cell_id mod 3 = 1\n");
-      printf("-j Relative strength of second intefering eNB (in dB) - cell_id mod 3 = 2\n");
-      printf("-o Carrier frequency offset in Hz\n");
-      printf("-N Nid_cell\n");
-      printf("-R N_RB_DL\n");
-      printf("-O oversampling factor (1,2,4,8,16)\n");
-      printf("-A Interpolation_filname Run with Abstraction to generate Scatter plot using interpolation polynomial in file\n");
-      //printf("-C Generate Calibration information for Abstraction (effective SNR adjustment to remove Pe bias w.r.t. AWGN)\n");
-      printf("-f Output filename (.txt format) for Pe/SNR results\n");
-      printf("-F Input filename (.txt format) for RX conformance testing\n");
-      printf("-i Enter number of ofdm symbols for pucch\n");
-      printf("-I Starting symbol index for pucch\n");
-      printf("-r PUCCH starting PRB\n");
-      printf("-q PUCCH number of PRB\n");
-      printf("-P Enter the format of PUCCH\n");
-      printf("-b number of HARQ bits (1-2)\n");
-      printf("-B payload to be transmitted on PUCCH\n");
-      printf("-m initial cyclic shift m0\n");
-      printf("-T to check nacktoack miss for format 1\n");
       exit (-1);
       break;
     }